#Nautech autohelm 2000 manual manual#

Where II is ncccessary lo nllach Ihe aulopilol lo a verlical lace such as the cockpit srdewall a canlrlever sockel assembly is used. Posilron the tiller bracket on Ihe cenlre line (upper/lower) 01 the tiller and eslablish lhe control dimensions A and B.Дiameler clearance holes through Ihe cenlre line 01 the Irtter.Д Bond lhe lixing bolls in place wilh epoxy adhesive and fully lighlen the nuts. Where the herghl 01 Ihe loller above or below Ihe cockpil seat or mounting plane is such lhal slandard mounling is not practicat a range of tiller brackels allows the loller pin o&et lo be varied. The prrshrod lengllr IWI~ be simply exlended using one 01 Ilre slandard pushrod exlensions. II il is not possible lo inslall Ihe drive unil directly onto Ihe cockpil seal or tiller as described, one 01 the lollowing accessories (or combinalion) will ensure a perfect inslallalion. Ensure lhal:-ДЄil holes are drilled to correcl size and where necessary reinlorcing is provrded. Note The aulopilol is capable 01 generating high pushrod loads. Lnslall the mounling sockel using Iwo par1 epoxy adhesive. (1вЂќ) carelully reinforce Ihe under surface wilh a plywood plale bonded into position. II Ihe slruclure thickness al Ihe mounling posilion is less Ihan 25mm Using a Iwo parl epoxy adhesive such as Araldile, bond the tiller pin into place.Д Drill 12.5nlrn (l/2вЂќ) hole x 25rnrn (1вЂќ) deep inlo Ihe starboard cockpil seal. Never force the changeover switch, light pressure only Is required.ДЄlter eslahlrshrng Ihe conlrol dimensions the Aulohelm 2000 can usually be mounled drreclly onto the Starboard cockprl seal (Fig 3). Use a screwdriver to rotate lhe switch anli.clockwise until the endstop is reached (Fig. When this is the case, the changeover switch will require adjustment as lollows.

In certain circumslances it may be more convenient to mount the unit on lhe porthand side.

Ensure the measurements are at right angles as shown. Is measured on the STARBOARD side of the cockpit) using masking tape to locate the fixing points. After connection to the yachtвЂ™s 12 volt electrical system the unit becomes operational.ДЇor correcl installation two basic dimensions are critical (Fig.l):-Д¬lamp Ihe tiller on the yachtвЂ™s cenlre line and mark elf dimensions A and The drive unil is mounled belween the toiler and a single allachmenl poinl on the yachtвЂ™s structure. After filling the equipment it is only necessary lo make a single adjustment lo the control unit lo match the aulopilols response lo Ihe sleenng characlerislics 01 your vessel. The syslem is designed lor owner inslallalion which aided by Ihe lollowing guide should prove lo be a simple and inleresling job. In case 01 any dillicully please conlacl our Technical Sales Deparlmenl lor assislance. This can be exlended by adding any of Ihe following a c c e s s o r i e s :Д¬ockpil and loller conliguralions vary widely and lo ensure your AulohclmДў000 inslallalion is as neal and secure as possible a lull range ol lillrng accessones is available lrom aulhorised Aulohelm slockisls. The basic system comprises Ihe main control unit, liller drive unil and basic mounting fillings. II will provide precise powerful sleering lor sailing yachls up lo The names Raytheon and RTN are owned by the Raytheon Company.ДЄulohelm 2000 is an up.to-lhe-minule digital liller autopilot which shares Ihe same microprocessor Iechnology buill into our biggest and mosl sophisticaled lully inslalled pilols.

#Nautech autohelm 2000 manual manual#

Distributed by Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine.